Scantech Vega V-1010 Manuel d'utilisateur télécharger pdf (Page 11)

Scantech-ID VEGA Linear Imager 7

Any operation must comply with the conditions below:

(a) The equipment will not cause any severe interference.

(b) The equipment can avoid any interference from environment.

Statement:

This product is classified as B class product.

In environment this product may cause some interference. In

this situation the user may do something to avoid interference.

1.3 SCANNER LABELLING

One label is present on the housing of the VEGA as indicated in the figure

below.

This label is attached by the manufacturer and should not be removed. The

scanner serial number is found on this label. This official registration is strictly

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 120 121

Handheld Bar code Scanner 1
Scantech-ID VEGA 3
Table of contents 5
Introduction 8
Chapter 1 Product Safety 9
1.1 SAFETY & CAUTION 10
1.2 FCC WARNING 10
1.3 SCANNER LABELLING 11
2.1 USE OF THE VEGA 14
3.1 V-1010 UNPACKING 16
3.2 V-1010 MOUNTING 17
4.1 V-1010BT UNPACKING 19
16 Configuring the VEGA 20
Pairing 21
18 Configuring the VEGA 22
Sleep Mode 23
Memory Mode 23
Chapter 5 Cover Display 24
5.1 SETUP COVER DISPLAY 25
Message Format 25
Change Cover Display 25
22 Configuring the VEGA 26
24 Configuring the VEGA 28
6.1 PREFACE 30
6.2 FACTORY DEFAULT SETTING 32
Chapter 7 Programming Codes 33
7.1 GENERAL PROCESS 34
Abort Configuration 34
Set All Default 35
Version Information 35
7.2 INTERFACE SELECTION 36
Interface 36
Scanner Pincode Mode 38
Scanner Pincode Setup 39
7.4 BLUETOOTH CRADLE SETUP 40
Cradle Pincode Mode 40
Cradle Pincode Setup 40
7.5 SCANNER OPERATION 41
Reading Mode 41
Good Read LED Control 41
Beeper Option 42
Reading Level 42
Accurany / Redundant Scan 42
Reverse Output Characters 43
7.6 RS232 MODE PARAMETERS 44
Baud Rate 44
Data/Stop Bits 45
Handshaking 46
Terminal Type 47
Country/Language 48
Upper/Lower Case 49
Interscan Code Delay 50
7.8 OUTPUT CHARACTERS 51
Select Terminator 51
7.9 CODE TYPE 52
Barcode Selections 52
50 Miscellaneous Parameters 54
7.10 UPC/EAN/JAN PARAMETERS 56
Reading Type 56
Supplemental Setup 57
Check Digit Transmission 58
7.11 CODE 39 PARAMETERS 59
Type of Code 59
Output Start/Stop Character 59
Decode Asterisk 60
Set Up Code Length 60
7.12 CODE 128 PARAMETERS 62
Append FNC2 62
60 Miscellaneous Parameters 64
Set Up Number of Character 65
Brazilian Banking Code 65
66 Miscellaneous Parameters 70
68 Miscellaneous Parameters 72
7.17 CODE 93 PARAMETERS 76
7.18 CODE 11 PARAMETERS 78
76 Miscellaneous Parameters 80
7.20 TELEPEN PARAMETERS 82
Check Digit Transmission 84
Application ID 84
Symbology ID 84
Symbology ID 86
Default Barcode ID 88
8.1 BAR CODE ID 88
User Define Code ID 89
86 Miscellaneous Parameters 90
Setup Insertion 91
Insertion Set Number 92
Symbologies Selection 93
90 Miscellaneous Parameters 94
Characters to be Inserted 95
8.3 CHARACTER DELETION 96
Deletion Set Number 97
Code Type to be Delete 98
96 Miscellaneous Parameters 100
Appendixes 101
B ASCII TABLE 103
Less than 105
Greater than 105
Underscore 107
C FUNCTION KEY TABLE 109
E TECHNICAL SPECIFICATIONS 111
(V-1010 wired model) 112
(V-1010BT wireless model) 112
F SCAN MAP 114
G LED INDICATOR STATUS 116
1234 5670 117
1 234567 890128 117
12345 67890 118
123456 118
I OVERVIEW MODEL NUMBERS 119
Quick Configuration 120

Commentaires sur ces manuels

Pas de commentaire

Scantech Vega V-1010 Manuel d'utilisateur Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Lecteurs de codes-barres Scantech Vega V-1010