Scantech Vega V-1010 Manuel d'utilisateur télécharger pdf (Page 53)

Scantech-ID VEGA Linear Imager 49

6.10.4 Set Up Code Length

To set the fixed length: (2 sets Available)

1. Scan the “Begin” programming code of the desired

set

2. Go to the Decimal Value Tables in Appendix A, scan

programming codes that represents the length to be

read.

3. Scan the “Complete” programming code of the desired

set.

Repeat the steps 1 – 3 to set additional lengths

Fixed Length 1

Set

Set Begin

Decimal Value See Appendix A

Set Complete

Fixed Length 2

Set

Set Begin

Decimal Value See Appendix A

Set Complete

1 2 ... 48 49 50 51 52 53 54 55 56 57 58 ... 107 108

VEGA V-1010 Linear Imager 1
Scantech-ID VEGA 3
Table of contents 5
Introduction 10
Chapter 1 Product Safety 11
1.1 SAFETY & CAUTION 12
1.2 FCC WARNING 13
2.1 USE OF THE VEGA 15
16
3.1 V-1010 UNPACKING 17
Chapter 4 Cover Display 18
Change Cover Display 20
18 Configuring the VEGA 22
5.1 PREFACE 24
Programming Codes 24
5.2 FACTORY DEFAULT SETTING 26
Chapter 6 Programming Codes 27
6.1 GENERAL PROCESS 28
Abort Configuration 28
Set All Default 29
Version Information 29
6.2 INTERFACE SELECTION 30
Interface 30
6.3 SCANNER OPERATION 30
Reading Mode 30
Good Read LED Control 31
Beeper Option 31
Reading Level 32
Accurany / Redundant Scan 32
Reverse Output Characters 33
6.4 RS232 MODE PARAMETERS 33
Baud Rate 33
Data/Stop Bits 34
Handshaking 35
Terminal Type 36
Country/Language 37
Upper/Lower Case 38
Capslock Detection 38
Character by ALT Method 39
Select Numerical Pad 39
Interscan Code Delay 40
6.6 OUTPUT CHARACTERS 41
Select Terminator 41
6.7 CODE TYPE 42
Barcode Selections 42
40 Miscellaneous Parameters 44
6.8 UPC/EAN/JAN PARAMETERS 46
Reading Type 46
Supplemental Setup 47
Check Digit Transmission 48
6.9 CODE 39 PARAMETERS 49
Type of Code 49
Output Start/Stop Character 49
Decode Asterisk 50
Set Up Code Length 50
6.10 CODE 128 PARAMETERS 52
Append FNC2 52
50 Miscellaneous Parameters 54
Set Up Number of Character 55
Brazilian Banking Code 55
56 Miscellaneous Parameters 60
58 Miscellaneous Parameters 62
Transmission 63
6.15 CODE 93 PARAMETERS 66
6.16 CODE 11 PARAMETERS 68
66 Miscellaneous Parameters 70
6.18 TELEPEN PARAMETERS 72
Check Digit Transmission 74
Application ID 74
Symbology ID 74
Symbology ID 76
7.1 BAR CODE ID 78
Default Barcode ID 78
User Define Code ID 79
76 Miscellaneous Parameters 80
Setup Insertion 81
Insertion Set Number 82
Symbologies Selection 83
80 Miscellaneous Parameters 84
Characters to be Inserted 85
7.3 CHARACTER DELETION 86
Deletion Set Number 87
Code Type to be Delete 88
86 Miscellaneous Parameters 90
Appendixes 91
B. ASCII TABLE 93
Less than 95
Greater than 95
Underscore 97
C. FUNCTION KEY TABLE 99
E. TECHNICAL SPECIFICATIONS 101
F. SCAN MAP 102
1234 5670 104
1 234567 890128 104
12345 67890 105
1 23456 105
H. OVERVIEW MODEL NUMBERS 106
Quick Configuration 107

Commentaires sur ces manuels

Pas de commentaire

Scantech Vega V-1010 Manuel d'utilisateur Page 53

Commentaires sur ces manuels

Produits connexes et manuels pour Lecteurs de codes-barres Scantech Vega V-1010